The aqueous polyurethane enamel 58510 Overview: Water Polyurethane Enamel is a waterborne two-component polyurethane enamel. With excellent gloss and color retention. Easy to clean. Uses: As a waterborne epoxy paint matching durable finish coat for mild to moderately corrosive environment. Temperature: exposure to dry conditions the maximum temperature: 120 ° C Physical parameters: Color / Color: white / black 10000/19990 finish: bright light Volume Solids: 49 ± 1% 43 ± 1% theory coating Cloth rate: 12.3 m 2 / liter (40 microns dry basis) 10.8 m 2 / liter (40 microns dry basis) Flash point:> 93 ° C> 93 ° C Weight: 1.4 kg / l 1.2 kg / liter Dry to touch: about 5 hours (20 ° C) for about 5 hours (20 ° C) VOC content (VOC): 55 g / l 60 g / liter Shelf life: Construction Description: Mixing ratio: Base 58519: Curing Agent 97760 = 8.5: 1.5 (volume ratio) with mechanical stirring carefully, with a 5-15% (by volume) of water to dilute. Construction method: Airless spray air spray Thinning: Shimizu Shimizu (maximum volume) (5-15%) (5-15%) Pot life: 2 hours (° C) orifices: 0.28-0.38 mm discharge Pressure: 15.0 MPa (reference only practical time can be adjusted) Tools cleaning: water film thickness: Dry: 40 microns wet film: 75 microns (diluted 15%: 100 microns) recoat: Minimum: 5 hours ( 20 ° C) Maximum: 7 days (20 ° C) Safety: Be careful using this product. And use before use, please note on the package label precautions. Furthermore, it should comply with the safety regulations of the State or local government regulations. Avoid breathing and swallowing, the FDA does not make contact with skin and eyes. Precautions must be taken against fire and explosion and environmental protection. Construction of this product only in well ventilated areas. Construction conditions: construction and curing must be carried out at above 10 ° C. Please clean dry surface construction, surface temperature above the dew point to avoid condensation. When dry relative humidity: 80% or less, the best need good ventilation in 40-60% and dry construction. Construction and drying to remove water vapor released in about 75 m3 / l paint ventilation equipment (20 ° C). (Relative humidity of the air supply 40%) Preceding coat: water-based epoxy primer 18500 or according to specification. Touch up: None Notes: Operating temperature: When the paint at temperatures higher than 100 ° C, there will be a slight discoloration. Gloss: Other gloss aqueous polyurethane enamel 58513 available offers. Film thicknesses: May and parts of the use of non-recommended film thickness depending on the purpose, but this will alter spreading rate, influence drying time and recoat interval. Normal dry film thickness in the range 30-60 microns. The aqueous polyurethane enamel 158,510 can not be too thick film construction (no more than 80-90 microns), because the film will be reduced foaming gloss. Recoat: minimum recoating intervals Construction waterborne epoxy primer 18500 is 3 hours (20 ° C) water-based epoxy primer 18500 can also choose 20 ° C and 45 minutes later came a heated 40 ° C 1 小时After recoating. Cleaning of tools: Tools after construction please immediately wash with water or warm soapy water. Available dried paint residue cleaner 99610 thoroughly cleaned. Save / Shelf life: Please within 5-40 ° C temperature range storage temperature is above 30 ° C shelf life will be shortened. Avoid frost during storage and transport. NOTE: Curing Agent 97760 pairs are sensitive to moisture. Please put in a dry place to store, reclosable lid. Open curing agent cans carefully overvoltage. Gary | ?? Sales Phone:? 021-6958010024 hour free service hotline: 17749768756 Fax: 021-69580100-816 QQ: 2477229652 Mail: 2477229652@qq.com?